雨予報だったけれども日中はさして降らなかったので、残る外周りの作業、庇
の内側仕上げをしました。廃物の蛍光灯を取り付けました。庇の内側をアルミ
やステンレスの0.1t板で覆ったので、(かなりの金額になりました。30cm x
120cm で2000円弱する)光量が稼げるのでは。下側にはツインカーボの蓋をこ
れから作ります。
床とロフト床のニス塗りもしました。あともう一回塗って終了かな。
西側の窓に、ロック用の窓ハンドルと開放状態で固定するためのヒンジをつけ
ました。この窓ハンドルはなんと2300円もする。窓自体には1000円もかかって
ないのに。
新しいデスクトップ機も少しづつ整備してます。マウスコンピュータの
Lm-AS425Sという機種。pciide0: bus-master DMA support present, but
unused (no driver support)というのが気になるけど、まぁそんなパフォーマ
ンスを気にするような用途じゃないし。動けばよし。
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 4.99.66 (CRESCENTMOON) #0: Sat Jun 21 11:56:36 JST 2008
uch@crecentmoon:/usr/work/src/sys/arch/i386/compile/obj/CRESCENTMOON
total memory = 2815 MB
avail memory = 2753 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
ECS A780GM-M (1.0)
mainbus0 (root)
mainbus0: Intel MP Specification (Version 1.4) (AMD RD790 )
cpu0 at mainbus0 apid 0: AMD 686-class, 2700MHz, id 0x60fb2
cpu1 at mainbus0 apid 1: AMD 686-class, 2700MHz, id 0x60fb2
mpbios: bus 0 is type PCI
mpbios: bus 1 is type PCI
mpbios: bus 2 is type PCI
mpbios: bus 3 is type PCI
mpbios: bus 4 is type ISA
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 21, 24 pins
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x1022 product 0x9600 (rev. 0x00)
ppb0 at pci0 dev 1 function 0: vendor 0x1019 product 0x9602 (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 5 function 0: vendor 0x1002 product 0x9610 (rev. 0x00)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
ppb1 at pci0 dev 7 function 0: vendor 0x1022 product 0x9607 (rev. 0x00)
ppb1: unsupported PCI Express version
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
re0 at pci2 dev 0 function 0: RealTek 8168B/8111B PCIe Gigabit Ethernet (rev. 0x02)
re0: interrupting at ioapic0 pin 19
re0: Unknown revision (0x3c400000)
re0: Ethernet address 00:1e:90:b5:ae:4f
re0: using 256 tx descriptors
rgephy0 at re0 phy 7: RTL8169S/8110S/8211 1000BASE-T media interface, rev. 2
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
pciide0 at pci0 dev 17 function 0
pciide0: vendor 0x1002 product 0x4390 (rev. 0x00)
pciide0: bus-master DMA support present, but unused (no driver support)
pciide0: primary channel configured to native-PCI mode
pciide0: using ioapic0 pin 22 for native-PCI interrupt
atabus0 at pciide0 channel 0
pciide0: secondary channel configured to native-PCI mode
atabus1 at pciide0 channel 1
ohci0 at pci0 dev 18 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci0: interrupting at ioapic0 pin 16
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 18 function 1: vendor 0x1002 product 0x4398 (rev. 0x00)
ohci1: interrupting at ioapic0 pin 16
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
ehci0 at pci0 dev 18 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci0: interrupting at ioapic0 pin 17
ehci0: dropped intr workaround enabled
ehci0: EHCI version 1.0
ehci0: companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
ohci2 at pci0 dev 19 function 0: vendor 0x1002 product 0x4397 (rev. 0x00)
ohci2: interrupting at ioapic0 pin 18
ohci2: OHCI version 1.0, legacy support
usb3 at ohci2: USB revision 1.0
ohci3 at pci0 dev 19 function 1: vendor 0x1002 product 0x4398 (rev. 0x00)
ohci3: interrupting at ioapic0 pin 18
ohci3: OHCI version 1.0, legacy support
usb4 at ohci3: USB revision 1.0
ehci1 at pci0 dev 19 function 2: vendor 0x1002 product 0x4396 (rev. 0x00)
ehci1: interrupting at ioapic0 pin 19
ehci1: dropped intr workaround enabled
ehci1: EHCI version 1.0
ehci1: companion controllers, 3 ports each: ohci2 ohci3
usb5 at ehci1: USB revision 2.0
piixpm0 at pci0 dev 20 function 0
piixpm0: vendor 0x1002 product 0x4385 (rev. 0x3a)
piixpm0: interrupting at SMI
iic0 at piixpm0: I2C bus
pciide1 at pci0 dev 20 function 1
pciide1: vendor 0x1002 product 0x439c (rev. 0x00)
pciide1: bus-master DMA support present, but unused (no driver support)
pciide1: primary channel configured to compatibility mode
pciide1: primary channel ignored (not responding; disabled or no drives?)
pciide1: secondary channel configured to compatibility mode
pciide1: secondary channel ignored (not responding; disabled or no drives?)
azalia0 at pci0 dev 20 function 2: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 16
azalia0: host: 0x1002/0x4383 (rev. 0), HDA rev. 1.0
pcib0 at pci0 dev 20 function 3
pcib0: vendor 0x1002 product 0x439d (rev. 0x00)
ppb2 at pci0 dev 20 function 4: vendor 0x1002 product 0x4384 (rev. 0x00)
pci3 at ppb2 bus 3
pci3: i/o space enabled
ohci4 at pci0 dev 20 function 5: vendor 0x1002 product 0x4399 (rev. 0x00)
ohci4: interrupting at ioapic0 pin 18
ohci4: OHCI version 1.0, legacy support
usb6 at ohci4: USB revision 1.0
pchb1 at pci0 dev 24 function 0
pchb1: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb2 at pci0 dev 24 function 1
pchb2: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb3 at pci0 dev 24 function 2
pchb3: vendor 0x1022 product 0x1102 (rev. 0x00)
amdtemp0 at pci0 dev 24 function 3
amdtemp0: AMD CPU Temperature Sensors (K8: core rev BH-G2)
isa0 at pcib0
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
attimer0 at isa0 port 0x40-0x43: AT Timer
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker (CPU-intensive output)
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0-0xff
npx0: reported by CPUID; using exception 16
attimer0: attached to pcppi0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[0]: Realtek ALC888 (rev. 0.1), HDA rev. 1.0
audio0 at azalia0: full duplex, independent
uhub0 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb4: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
uhub2 at usb2: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 6 ports with 6 removable, self powered
uhub3 at usb1: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 3 ports with 3 removable, self powered
uhub4 at usb5: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 6 ports with 6 removable, self powered
uhub5 at usb3: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub5: 3 ports with 3 removable, self powered
uhub6 at usb6: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub6: 2 ports with 2 removable, self powered
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 1: <HL-DT-ST DVDRAM GH20NS10, K1585JL4329, EL01> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0 at atabus0 drive 0: <WDC WD3200AAKS-00B3A0>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 298 GB, 620181 cyl, 16 head, 63 sec, 512 bytes/sect x 625142448 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
umass0 at uhub4 port 3 configuration 1 interface 0
umass0: Generic Mass Storage Device, rev 2.00/1.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 4 luns per target
sd0 at scsibus0 target 0 lun 0: <Generic, USB SD Reader, 1.00> disk removable
sd0: drive offline
sd0(umass0:0:0:0): Check Condition on CDB: 0x00 00 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd0: unable to open device, error = 19
sd1 at scsibus0 target 0 lun 1: <Generic, USB CF Reader, 1.01> disk removable
sd1: drive offline
sd1(umass0:0:0:1): Check Condition on CDB: 0x00 20 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd1: unable to open device, error = 19
sd2 at scsibus0 target 0 lun 2: <Generic, USB SM Reader, 1.02> disk removable
sd2: drive offline
sd2(umass0:0:0:2): Check Condition on CDB: 0x00 40 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd2: unable to open device, error = 19
sd3 at scsibus0 target 0 lun 3: <Generic, USB MS Reader, 1.03> disk removable
sd3: drive offline
sd3(umass0:0:0:3): Check Condition on CDB: 0x00 60 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd3: unable to open device, error = 19
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
sd0(umass0:0:0:0): Check Condition on CDB: 0x00 00 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd1(umass0:0:0:1): Check Condition on CDB: 0x00 20 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd2(umass0:0:0:2): Check Condition on CDB: 0x00 40 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd3(umass0:0:0:3): Check Condition on CDB: 0x00 60 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd0(umass0:0:0:0): Check Condition on CDB: 0x00 00 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd1(umass0:0:0:1): Check Condition on CDB: 0x00 20 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd2(umass0:0:0:2): Check Condition on CDB: 0x00 40 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd3(umass0:0:0:3): Check Condition on CDB: 0x00 60 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd0(umass0:0:0:0): Check Condition on CDB: 0x00 00 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd1(umass0:0:0:1): Check Condition on CDB: 0x00 20 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd2(umass0:0:0:2): Check Condition on CDB: 0x00 40 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd3(umass0:0:0:3): Check Condition on CDB: 0x00 60 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd0(umass0:0:0:0): Check Condition on CDB: 0x00 00 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd1(umass0:0:0:1): Check Condition on CDB: 0x00 20 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd2(umass0:0:0:2): Check Condition on CDB: 0x00 40 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
sd3(umass0:0:0:3): Check Condition on CDB: 0x00 60 00 00 00 00
SENSE KEY: Not Ready
COMMAND INFO: 11162944 (0xaa5540)
ASC/ASCQ: Medium Not Present
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
